specification rsp-1500-5 model dc voltage rated current current range rated power output voltage adj. range line regulation load regulation setup, rise time hold up time (typ.) voltage range frequency range efficiency (typ.) input inrush current (typ.) leakage current over temperature working temp. current sharing output voltage trim alarm signal output remote on/off control auxiliary power(aux) working humidity storage temp., humidity temp. coefficient vibration mtbf dimension others note packing overload note.5 over voltage ac current (typ.) 5v 240a 0 ~ 240a 1200w 150mvp-p 4.5 ~ 5.5v 2.0% 0.5% 2.0% 1500ms, 100ms at full load 10ms at full load 14ms at full load 16ms at full load 90 ~ 264vac 127 ~ 370vdc 47~63hz 80% 17a/115vac 8a/230vac 30a/115vac 60a/230vac <2.0ma / 240vac 105 ~135% rated output power 5.75 ~ 6.75v protection type : constant current limiting unit will shut down o/p voltage after 5sec. re-power on to recover 13.8 ~ 16.8v 17 ~ 20.5v 27.6 ~ 32.4v 31 ~ 36.5v 57.6 ~ 67.2v protection type : shut down o/p voltage, re-power on to recover 95 5 (tsw2 ) detect on heatsink of power transistor protection type : shut down o/p voltage, recovers automatically after t emperature goes down -20 ~ +70 (refer to output load derating curve) please see the function manual please see the function manual please see the function manual please see the function manual 12v@0.1a(only for remote on/off control) 20~90% rh non-condensing -40 ~ +85 , 10 ~ 95% rh 0.05%/ (0 ~ 50 ) 10 ~ 500hz, 2g 10min./1cycle, 60min. each along x, y, z axes 62.6k hrs min. mil-hdbk-217f (25 ) 278*127*83.5mm (l*w*h) 2.6kg; 6pcs/16.6kg/1.54cuft 87% 87% 90% 90% 91% 0.5% 0.5% 0.5% 0.5% 0.5% 0.5% 0.5% 0.5% 0.5% 0.5% 1.0% 1.0% 1.0% 1.0% 1.0% 150mvp-p 10 ~ 13.5v 150mvp-p 13.5 ~ 16.5v 150mvp-p 20 ~ 26.4v 150mvp-p 24 ~ 30v 200mvp-p 43 ~ 56v 12v 125a 0 ~ 125a 1500w 15v 100a 0 ~ 100a 1500w 24v 63a 0 ~ 63a 1512w 27v 56a 0 ~ 56a 1512w 48v 32a 0 ~ 32a 1536w rsp-1500-12 rsp-1500-15 rsp-1500-24 rsp-1500-27 rsp-150 0-48 1. all parameters not specially mentioned are measured at 230vac input, r ated load and 25 of ambient temperature. 2. ripple & noise are measured at 20mhz of bandwidth by using a 12" twisted pair- wire terminated with a 0.1uf & 47uf parallel capacitor. 3. tolerance : includes set up tolerance, line regulation and load regula tion. 4. the power supply is considered a component which will be installed into a fi nal equipment. the final equipment must be re-confirmed that it still me ets emc directives. 5. derating may be needed under low input voltages. please check the derati ng curve for more details. file name:rsp-1500-spec 2007-03-19 3 power factor (typ.) 0.95/230vac 0.98/115vac at full load safety standards harmonic current ems immunity ul60950-1, tuv en60950-1 approved compliance to en55022 (cispr22) compliance to en61000-3-2,-3 compliance to en61000-4-2,3,4,5,6,8,11; env50204, en55024, l ight industry level, criteria a 1500w single output power supply r s p - 1 5 0 0 s e r i e s ripple & noise (max.) note.2 voltage tolerance note.3 emi conduction & radiation withstand voltage isolation resistance i/p-o/p:3kvac i/p-fg:1.5kvac o/p-fg:0.5kvac i/p-o/p, i/p-fg, o/p-fg:100m ohms/500vdc environment safety & function emc (note 4) protection universal ac input/full range zvs new technology ac input active surge current limiting high efficiency up to 91% built-in active pfc function,pf>0.95 protections: short circuit / overload / over voltage / over temperature forced air cooling by built-in dc ball bearing fan output voltage can be trimmed between 70~100% of the rated output voltage high power density 8.3w/inch current sharing up to 6000w(3+1) alarm signal output built-in 12v/0.1a auxiliary output for remote control built-in remote on-off control built-in remote sense function 3 years warranty features : rsg electronic components rsg electronic components gmbh sprendlinger landstr. 115 d-63069 offenbach/germany tel. +49 69 984047-0 fax +49 69 984047-77 info@rsg-electronic.de www.rsg-electronic.de ?nderungen vorbehalten / subject to change without notice
mechanical specification file name:rsp-1500-spec 2007-03-19 case no.943a unit:mm ac input terminal pin no. assignment pin no. 1 3 2 assignment ac/n ac/l control pin no. assignment(cn3) : pin no. pin no. 3 6 2 5 p ok gnd: power ok ground p ok: power ok signal rcg: remote on/off ground auxg: auxiliary ground rc1: remote on/off aux: auxiliary output 1 4 assignment assignment rcg p ok p ok gnd fg direction 93 air flow 16 i/p 3 2 -v 1 +v 17.5 10 13 240 11.2 278 4-m4 l=5 83.5 38 38.1 22.7 4-m4 l=5 127 11.2 240 led svr cn1 cn2 cn3 output 7 7 5 5 5 3 3 3 1 1 1 2 2 4 4 2 6 6 4 8 8 6 4 mating housing terminal hrs df11 hrs df11 or equivalent or equivalent block diagram pfc fosc : 70khz pwm fosc : 100khz fan o.v.p. -v +v rectifiers & filter -s +s circuit detection power aux remote control rc filter & rectifiers aux power (12v/0.1a) sharing load ls p ok limiting active current inrush control ing i/p switch- power rectifiers filter emi pwm & pfc pfc control o.t.p. o.l.p. control pin no. assignment(cn1,cn2) : pin no. pin no. 2 1 3,5,7 rcg: remote on/off ground rc2: trim: adjustment of output voltage remote on/off ls: load share -s : -remote sensing +s: +remote sensing assignment assignment rc2 rcg -s mating housing terminal hrs df11 hrs df11 or equivalent or equivalent 8 6 4 +s trim ls(current share) 1500w single output power supply r s p - 1 5 0 0 s e r i e s aux rc1 auxg rsg electronic components rsg electronic components gmbh sprendlinger landstr. 115 d-63069 offenbach/germany tel. +49 69 984047-0 fax +49 69 984047-77 info@rsg-electronic.de www.rsg-electronic.de ?nderungen vorbehalten / subject to change without notice
function manual 1.remote on/off (1)remote on/off control becomes available by applying voltage in cn1 & c n2 & cn3 (2)table 1.1 shows the specification of remote on/off function (3)fig.1.2 shows the example to connect remote on/off control functio n file name:rsp-1500-spec 2007-03-19 table 1.1 specification of remote on/off fig.1.2 examples of connecting remote on/off connection method sw logic output on sw open sw open sw open fig. 1.2(a) fig. 1.2(b) fig. 1.2(c) output off sw close sw close sw close 2.2k aux rc1 12v typ. auxg 150 rcg rc2 sw 620 5v 150 rc2 12v typ. rcg auxg 2.2k rc1 aux (a)using external voltage source (b)using internal 12v auxiliary output sw 150 rc2 12v typ. auxg sw rcg (c)using internal 12v auxiliary output 2.2k rc1 aux derating curve static characteristics ambient temperature ( ) load (%) 20 40 60 50 80 100 -20 0 10 20 30 40 45 50 60 70 input voltage (v) 60hz 100 90 80 70 60 load (%) ta=25 90 100 120 140 150 160 180 200 220 240 264 +5v +12v,+15v others (horizontal) 1500w single output power supply r s p - 1 5 0 0 s e r i e s rsg electronic components rsg electronic components gmbh sprendlinger landstr. 115 d-63069 offenbach/germany tel. +49 69 984047-0 fax +49 69 984047-77 info@rsg-electronic.de www.rsg-electronic.de ?nderungen vorbehalten / subject to change without notice
3.output voltage trim 4.current sharing (1)adjustment of output voltage is possible between 70~100%(typ.) o f the rated output which is shown in fig. 3.1 (1)parallel operation is available by connecting the units shown as bel ow (+s,-s and ls are connected mutually in parallel): (2)the voltage difference among each output should be minimized that le ss than 2% is required (3)the total output current must not exceed the value determined by the fol lowing equation (4) in parallel operation 4 units is the maximum, please consult the manufa cture for other applications (5) when remote sensing is used in parallel operation, the sensing wire mus t be connected only to the master unit (output current at parallel operation)=(the rated current per unit) x ( number of unit) x 0.9 file name:rsp-1500-spec 2007-03-19 (2)connecting a resistor externally between trim and-s on cn1 or cn2 tha t is shown in fig. 3.2. 2.alarm signal output (1)alarm signal is sent out through "p ok" & "p ok gnd" pins (2)an external voltage source is required for this function. the maxim um applied voltage is 50v and the maximum sink current is 10ma (3)table 2.1 explain the alarm function built-in the power supply fig. 2.2 internal circuit of p ok (open collector method) external voltage and r (the max. sink is 10ma and 50v) p ok gnd p ok trim cn1 or cn2 -s function p ok the signal is "low" when the power supply is 65% of the rated output voltage-power ok above low (0.5v max at 10ma) description output of alarm(p ok) the signal turns to be "high" when the power supply is under 65% of the rated output voltage-power fail high or open (external applied voltage 10ma max.) r v 0.1uf 100k r(0.5w) +s load v- v+ -s ls ls -s +s cn1 cn2 no.1(master) ac/l ac/n no.2(slave) ac/l ac/n ls v- +s -s ls -s +s cn1 cn2 v+ ac/n ac/l cn2 -s v- ls cn1 +s -s ls +s v+ ac/l ac/n ls v- +s -s ls -s +s cn1 cn2 v+ no.3(slave) no.4(slave) +v -v +s -s 1500w single output power supply r s p - 1 5 0 0 s e r i e s 470 0 1.8k open 70% 80% 90% 100% vout r fig. 3.1 external resistor (typical) fig. 3.2 output voltage trimming table 2.1 explanation of alarm rsg electronic components rsg electronic components gmbh sprendlinger landstr. 115 d-63069 offenbach/germany tel. +49 69 984047-0 fax +49 69 984047-77 info@rsg-electronic.de www.rsg-electronic.de ?nderungen vorbehalten / subject to change without notice
|
